Embossed Aluminum Sheet
video

Embossed Aluminum Sheet

GNEE supplies embossed aluminum sheet with a fine, non-directional texture rolled into the surface — most commonly stucco (orange peel), plus diamond (rhombus) and other patterns. The textured sheet keeps aluminum's lightweight, corrosion-resistant and formable character while reducing glare and hiding minor handling marks, which makes it a practical face for insulation jacketing, refrigeration, HVAC, appliance liners, automotive heat shields and architectural interiors.
Send Inquiry
Chat Now

Customer service is online. Enter the chat to get the latest quotation.

  • Spot stockSpot stock
  • CustomizeCustomize
  • Factory direct saleFactory direct sale
  • 7 days delivery7 days delivery
Product Introduction

Overview of Embossed Aluminum Sheet

Embossed aluminum sheet is aluminum sheet passed through patterned embossing rollers to raise a decorative or functional texture on one or both faces. Stucco embossed aluminum sheet carries a fine, irregular orange-peel texture and is the most widely used pattern. Unlike aluminum tread plate, which uses larger raised patterns for grip and flooring, embossed sheet uses a much finer, non-directional texture suited to clean industrial and decorative surfaces.

GNEE produces embossed aluminum sheet across the 1xxx, 3xxx and 5xxx series. The alloy and temper are selected for the forming and service requirement, while the embossing pattern is chosen for appearance, glare control and mark concealment rather than for load-bearing.

 

Stucco (Orange Peel) Embossed Aluminum Sheet

Stucco embossed aluminum sheet - also called orange peel embossed aluminum sheet - has a fine, irregular texture resembling traditional stucco or orange peel. It is the default pattern for pipe and duct insulation jacketing, refrigerator and freezer linings, HVAC panels and appliance faces because the texture breaks up reflections and makes small scratches or fingerprints less visible than on a smooth mill finish.

Commonly stocked grades for stucco embossed aluminum sheet are 1050, 1060, 1100, 3003, 3105 and 5052, in tempers from fully soft O to work-hardened H1x / H2x conditions, confirmed by the buyer's forming method.

 

Advantages of Embossed Aluminum Sheet

Corrosion resistance - the wrought aluminum surface forms a stable oxide film and suits indoor and mild outdoor use.

Formability - the O temper bends, draws and spins with minimal springback; harder tempers add strength where needed.

Lightweight - density 2.68–2.73 g/cm³ keeps panels and cladding easy to handle.

Low-glare, mark-concealing surface - the non-directional texture hides small scratches and fingerprints.

Good thermal behaviour - high conductivity (138–234 W/(m·K) by alloy) supports insulation and heat-dissipation roles.

High reflectivity (1xxx) - 1050 / 1060 give reflectivity above 85% (indicative), suited to lighting reflectors and solar backs.

Recyclable - 100% recyclable aluminum with no loss of properties.

 

Embossing Patterns of Embossed Aluminum Sheet

The embossed texture is a physical surface finish applied by patterned rollers. Several textures are available so the buyer can match appearance and function.

Orange peel embossed aluminum sheet texture

The fine, non-directional orange-peel pattern - the stucco standard - used across insulation, refrigeration, HVAC, appliance and decorative work where low glare and mark concealment matter most.

Diamond (rhombus) embossed aluminum sheet texture

A more regular raised geometric pattern that gives a stronger textured appearance. Diamond embossed aluminum sheet is chosen when a defined pattern is preferred for visual or light grip purposes on panels and equipment housings.

Custom embossed aluminum sheet patterns

Hammer / cobblestone, hemisphere and water-ripple textures are available on request for specific decorative or branded components. Tell us the pattern sample or drawing and we confirm roll availability.

Send an Inquiry Now

 

Embossed Aluminum Sheet Pattern Type

 

Chemical Composition of Embossed Aluminum Sheet

Embossed aluminum sheet is produced on several wrought alloys. The table below lists standard composition limits (mass fraction, %) following ASTM B209 and GB/T 3190. Final mill-certificate values are supplied per order.

Alloy Si Fe Cu Mn Mg Zn Al min
1050 0.25 0.40 0.05 0.05 0.05 0.05 99.50
1060 0.25 0.35 0.05 0.03 0.03 0.05 99.60
1100 0.95 (Si+Fe) - 0.05–0.20 0.05 - 0.10 99.00
3003 0.6 0.7 0.05–0.20 1.0–1.5 - 0.10 rem
3105 0.6 0.7 0.30 0.30–0.8 0.20–0.8 0.40 rem
5052 0.25 0.40 0.10 0.10 2.2–2.8 0.10 rem

"rem" = remainder (aluminum balance). Chromium, titanium and individual impurity limits follow the relevant standard and are supplied on the mill test certificate.

 

Mechanical Properties of Embossed Aluminum Sheet

Representative values for the O (annealed) temper are listed below (indicative; actual figures vary with thickness, temper and test method, and should be confirmed against ASTM B209 / EN 485 and the ordered specification).

Property (O temper) 1050 1060 1100 3003 3105 5052
Tensile strength (UTS), MPa 60–100 60–95 75–105 95–130 115–165 170–215
Yield strength (0.2%), MPa 20–40 20–35 25–45 35–55 40–75 65–95
Elongation (50 mm), % 20–30 20–28 25–35 20–30 15–28 20–28
Density, g/cm³ 2.70 2.70 2.71 2.73 2.72 2.68
Thermal conductivity, W/(m·K) 229 234 222 193 180 138

Work-hardened tempers (H12–H32) raise tensile and yield strength and lower elongation. For a specific temper, confirm the exact values from the mill test certificate.

 

Specifications of Embossed Aluminum Sheet

Parameter GNEE embossed aluminum sheet
Alloy 1050, 1060, 1100, 3003, 3105, 5052
Temper O, H12, H14, H16, H18, H22, H24, H26, H32 (confirmed per order)
Thickness 0.2–3.0 mm (0.1 mm ultra-thin O on request)
Width 500–1500 mm (other widths on request)
Length Cut-to-length, customized
Embossing depth 0.08–0.25 mm
Pattern Stucco / orange peel, diamond / rhombus, hammer, hemisphere (custom on request)
Surface finish Mill finish, color coated, anodized, bright / mirror
Standards ASTM B209, ASTM B632, EN 485-2, EN 573-3, GB/T 3880.2, GB/T 3190
MOQ Flexible - both small trial orders and large-volume orders accepted
Lead time 15–30 days

Pricing is built on the SMM (Shanghai Metals Market) primary aluminum ingot reference plus rolling, embossing and surface-treatment premiums. Confirm the current quotation with our sales team for your exact alloy, temper, size and finish.

 

Embossed Aluminum Sheet

 

Surface Treatment of Embossed Aluminum Sheet

The embossed face can be finished to suit the application. The base alloy and temper are selected first; the surface system is added per requirement.

Mill finish - natural aluminum surface with the embossed texture; lowest cost, fully corrosion resistant.

Color coated (PE / HDP / PVDF) - polyester, high-durability polyester or fluorocarbon coating for weather and colour; indicative service life roughly 7–8 years (PE), up to 15 years (HDP) and 20–25 years (PVDF) depending on environment.

Anodized - dense oxide film (typically 3–25 µm) for wear and corrosion resistance; also a base for dyeing.

Bright / mirror - polished reflective surface for lighting and decorative panels.

 

Surface Treatment Of Embossed Aluminum Sheet

 

Applications of Embossed Aluminum Sheet

Because embossed aluminum sheet is lightweight, corrosion resistant and formable, with a glare-free, mark-concealing face, it fits applications where a clean, consistent aluminum surface is needed more than high strength.

Pipe & duct insulation jacketingOuter metal skin for insulation systems; texture hides installation marks.

Refrigeration liningsFreezer, cold-room and refrigerator panels - light, corrosion resistant.

HVAC equipmentHousings, duct parts and equipment panels fabricated from sheet.

Appliance & equipment panelsCabinet and machine housings needing a consistent aluminum face.

Architectural interiorsCeiling, wall cladding and decorative components.

Lighting & reflectorsBright-finish embossed sheet for reflector and decorative lighting use.

 

Embossed Aluminum Sheet for Pipe and Duct Insulation

Stucco embossed aluminum sheet is widely used as the outer metal skin of pipe and duct insulation jacketing. The textured face reduces the visibility of minor installation marks and gives a clean industrial appearance, while aluminum's corrosion resistance suits indoor and mild outdoor service. Where a project needs a backing system, the moisture-barrier build-up is specified separately rather than ordered as bare embossed sheet.

 

Embossed Aluminum Heat Shield Sheet for Automotive

Embossed aluminum heat shield sheet is used in automotive and equipment applications where a lightweight, reflective, formable metal skin helps manage radiant heat. Thin O-temper sheet draws and bends around shaped components, and the textured face adds stiffness and a consistent finish. Alloy and temper are confirmed by the forming method and the temperature the part will see in service.

 

Embossed Aluminum Sheet for Oven Cavity and Appliance Insulation

Thin 1050 / 1060 O embossed aluminum sheet, typically 0.1–0.5 mm, is used for refrigerator, freezer and oven cavity insulation liners and broader appliance insulation panels. The O temper draws and bends without cracking, and the surface can be supplied oil-free and with a cleanliness report for appliance production lines. Ultra-thin 0.1 mm O is a custom thin gauge confirmed per specification rather than standard stock.

Stucco embossed aluminum sheet for appliance insulation is valued because the textured face resists fingerprints and minor marks during assembly, and the high-purity 1xxx grade gives reflectivity above 85% (indicative) for reflective or thermal roles.

Embossed Aluminum Sheet For Pipe And Duct Insulation
Embossed Aluminum Sheet for Pipe and Duct Insulation
Embossed Aluminum Heat Shield Sheet For Automotive
Embossed Aluminum Heat Shield Sheet for Automotive
Embossed Aluminum Sheet For Oven Cavity
Embossed Aluminum Sheet for Oven Cavity

Thickness Selection for Embossed Aluminum Sheet

Embossed aluminum sheet spans 0.2–3.0 mm, with ultra-thin 0.1 mm O available on request. The table maps typical thickness bands to common uses so buyers can specify the right gauge up front.

Thickness band Typical use Specifying note
0.1–0.5 mm Appliance inner liners (refrigerator / freezer / oven insulation), thin lighting reflectors O temper for deep drawing and bending without cracks; surface supplied oil-free
0.5–1.2 mm Refrigeration panels, HVAC housings, indoor decoration Mainstream band for formed panels
1.2–2.0 mm Larger equipment cladding, transport interior panels Stiffer stock for larger panels
2.0–3.0 mm Heavy equipment outer panels, structural decoration Heavier band, less common for fine stucco texture

Thickness bands are indicative. Tell us the forming method and final part so we confirm the workable gauge and temper.

 

Contact Our Engineers Today

 

Embossed Aluminum Sheet Alloy Comparison

All listed grades are non-heat-treatable wrought alloys with good corrosion resistance and formability. Choose by required formability, strength and thermal behaviour rather than by surface pattern.

Alloy Al min % UTS (O) MPa Yield (O) MPa Elong (O) % Density g/cm³ Thermal cond. W/(m·K) Where it fits
1050 99.50 60–100 20–40 20–30 2.70 229 Insulation, refrigeration, decorative, reflective
1060 99.60 60–95 20–35 20–28 2.70 234 Insulation, general fabrication
1100 99.00 75–105 25–45 25–35 2.71 222 Nameplates, spun and decorative parts
3003 rem 95–130 35–55 20–30 2.73 193 HVAC, parts needing more strength
3105 rem 115–165 40–75 15–28 2.72 180 Architectural, siding, formed panels
5052 rem 170–215 65–95 20–28 2.68 138 Higher-strength, mild marine / equipment

O-temper values are indicative and depend on thickness and test standard (ASTM B209 / EN 485). For H1x / H2x tempers the strength is higher and elongation lower. Confirm per ordered specification.

 

Packaging and Shipping of Embossed Aluminum Sheet

GNEE packs embossed aluminum sheet to protect the textured face during transit:

Interleaving paper between sheets and a PE / PVC protective film on the visible face.

Export packing on wooden pallets, in wooden cases or with steel frames, selected by size and destination.

Worldwide delivery by sea, air or land freight arranged to the buyer's requirement.

 

aluminum plate packaging1

 

Quality Assurance for Embossed Aluminum Sheet

Buyers of embossed aluminum sheet most often lose orders on four points: thickness / embossing tolerance, surface oil, white rust on opening, and wrong temper for the forming process. GNEE addresses each with verifiable, shipment-level documents.

Thickness and embossing-depth report for embossed aluminum sheet

We supply per-sheet measured thickness (multi-point) and embossing depth with the shipment - not nominal values only - so the material fits jacketing and formed parts without rework.

Surface cleanliness of embossed aluminum sheet

For appliance and food-contact inner liners we degrease the surface and provide a cleanliness report with an oil-free commitment, so the sheet passes appliance and food-grade lines. If a food-contact standard is required (FDA 21 CFR / EC 1935/2004 or equivalent), confirm it at quotation.

Moisture barrier for embossed aluminum sheet jacketing

For pipe and duct insulation we offer a moisture-barrier build-up (Polylam / Kraft) with desiccant and supply loading photos, preventing white rust when the sheet is opened on site.

Temper and forming-process confirmation for embossed aluminum sheet

Before production we confirm the forming method (deep drawing, bending, spinning) and supply the correct temper - O for deep draw, avoiding H-temper cracking - with a temper-to-process reference on request.

 

Why Choose GNEE for Embossed Aluminum Sheet

Established 2008 - GNEE has supplied aluminum products since 2008.

100+ countries served - export experience across more than 100 countries and regions.

Flexible order size - small trial orders and large-volume / full-container / contract orders are both accepted.

Standards-based production - ASTM B209, ASTM B632, EN 485-2, EN 573-3, GB/T 3880.2 and GB/T 3190, with mill test certificates on request.

Document support for export - we prepare MTC and can arrange EN 485 / CE / REACH (EU), ASTM B209 / B632 (North America), JIS / KS (Japan–Korea) and other project documents on request; the exact certificate depends on destination (To be confirmed).

Full customization - alloy, temper, thickness, width, pattern, coating and length confirmed to your specification.

Lead time 15–30 days - standard production window for most orders.

 

GNEE ALUMINUM

Client Visit 2

 

FAQ

What is embossed aluminum sheet?

Embossed aluminum sheet is aluminum sheet passed through patterned embossing rollers to create a raised texture such as stucco (orange peel) or diamond (rhombus). The texture reduces glare, hides minor handling marks and gives a consistent decorative or industrial face, while keeping the lightweight and corrosion-resistant nature of aluminum.

Is embossed aluminum sheet the same as stucco embossed aluminum sheet?

Embossed aluminum sheet is the broad category covering all textured sheets. Stucco embossed aluminum sheet is the most common type within it, with a fine, non-directional orange-peel texture. Buyers may also see it described as orange peel embossed aluminum sheet.

What is the difference between orange peel and diamond embossed aluminum sheet?

Orange peel (stucco) embossed aluminum sheet has a fine, irregular texture used for insulation, appliance and decorative faces where low glare matters. Diamond (rhombus) embossed aluminum sheet has a more regular raised geometric pattern and is chosen when a stronger textured appearance is wanted.

Which alloy should I choose for embossed aluminum sheet?

For insulation, refrigeration and decorative or reflective use, 1xxx grades (1050, 1060, 1100) give the best formability and corrosion resistance. For HVAC and parts needing more strength, 3003 or 3105 are typical. For higher mechanical strength, 5052 is selected. Alloy is chosen by forming need and service condition, not by pattern.

What thickness of embossed aluminum sheet is available?

Standard production runs 0.2–3.0 mm, with typical stock at 0.5–2.0 mm. Thickness, width (500–1500 mm) and length (cut-to-length) are confirmed per order. Ultra-thin 0.1 mm O is available on request for appliance liners.

Can embossed aluminum sheet be used for oven cavity and insulation?

Yes. Thin 1050 / 1060 O embossed aluminum sheet, typically 0.1–0.5 mm, is used for refrigerator, freezer and oven cavity insulation liners and appliance insulation panels. The O temper draws and bends without cracking, and the surface can be supplied oil-free for appliance lines.

Is embossed aluminum sheet suitable as a heat shield?

Yes. Embossed aluminum heat shield sheet is used in automotive and equipment applications where a lightweight, reflective, formable metal skin helps manage radiant heat. Alloy and temper are confirmed by the forming method and service temperature.

Can embossed aluminum sheet be color coated or anodized?

Yes. Mill finish is standard, and color-coated (PE / HDP / PVDF) or anodized finishes, as well as a bright mirror finish, can be supplied when a colour or extra protection is required. Confirm coating system, colour and gloss before production.

What is the lead time and MOQ for embossed aluminum sheet?

Lead time is 15–30 days. MOQ is flexible: both small trial orders and large-volume orders are accepted, and the exact minimum depends on alloy, size and finish.

 

Request a Quote for Embossed Aluminum Sheet

Send your embossed aluminum sheet specification

Tell us alloy, temper, thickness, width, length, pattern, surface finish and quantity - our team confirms the material specification and lead time.

 

Hot Tags: embossed aluminum sheet, China embossed aluminum sheet manufacturers

Send Inquiry

whatsapp

Phone

E-mail

Inquiry