6063 T6 Aluminium Angle Bar
Customer service is online. Enter the chat to get the latest quotation.
Spot stock
Customize
Factory direct sale
7 days delivery
What Is 6063 T6 Aluminum Angle?
6063 T6 aluminum angle is an extruded L-shaped section made from 6063, a 6xxx-series (Al-Mg-Si) heat-treatable alloy. After extrusion it is solution heat-treated and artificially aged to the T6 temper, which gives moderate strength, good atmospheric corrosion resistance, and an excellent surface for anodizing and powder coating. Its main advantage over many other structural alloys is extrudability and finish quality, so it is widely used for window and door frames, railings, display and shop-fitting profiles, solar mounting frames, and light structural framing. Equal angles have two legs of the same length; unequal angles have two different leg lengths.
Key Features of 6063 T6 Aluminum Angle
Good corrosion resistance in normal atmospheric and indoor environments; suitable for most architectural and light outdoor use, especially after anodizing.
Excellent surface finish: takes anodizing and powder coating well, giving a bright, uniform decorative appearance.
Moderate strength with good formability-adequate for framing, trim, and light structural roles, though lower than 6061 or 6082.
Easy to fabricate: cuts, drills, and welds readily with common shop processes; good machinability for an architectural alloy.
Lightweight and recyclable, reducing handling weight and supporting recycled-content requirements.
Chemical Composition of 6063 Aluminum Angle
The composition below follows ASTM B221 / EN 573-3 / GB/T 3190, given in weight percent with aluminum as balance.
| Element | Content (wt%) |
|---|---|
| Silicon (Si) | 0.20–0.60 |
| Iron (Fe) | ≤ 0.35 |
| Copper (Cu) | ≤ 0.10 |
| Manganese (Mn) | ≤ 0.10 |
| Magnesium (Mg) | 0.45–0.90 |
| Chromium (Cr) | ≤ 0.10 |
| Zinc (Zn) | ≤ 0.10 |
| Titanium (Ti) | ≤ 0.10 |
| Others, each / total | ≤ 0.05 / ≤ 0.15 |
| Aluminum (Al) | Balance |
Mechanical Properties of 6063 T6 Aluminum Angle
The table shows typical minimum values for extruded profiles. 6063 is most often supplied as T5 (as-extruded, aged) or T6 (solution heat-treated and aged); T6 gives higher strength for load-bearing sections.
| Temper | Tensile strength (MPa) | Yield strength (MPa) | Elongation (%) |
|---|---|---|---|
| T5 | ≥ 152 (22 ksi) | ≥ 110 (16 ksi) | ≥ 8 |
| T6 | ≥ 241 (35 ksi) | ≥ 214 (31 ksi) | ≥ 8 |
Values are per ASTM B221. EN 755-2 lists slightly lower minimums for T6 (205 MPa tensile, 170 MPa yield); GNEE supplies to the standard agreed in the order, and the exact figures on the mill test report depend on leg thickness. Density is about 2.70 g/cm³.

Available Sizes and Tempers of 6063 T6 Aluminum Angle
| Item | Specification |
|---|---|
| Grade | 6063 (EN AW-6063, UNS A96063, GB/T 6063) |
| Type | Equal angle and unequal angle |
| Equal leg size | 20 × 20 mm to 150 × 150 mm |
| Unequal leg size | 25 × 16 mm to 150 × 100 mm (typical) |
| Thickness | 2–12 mm |
| Standard length | 3 m / 6 m; cut-to-length and custom lengths on request |
| Tempers | T5, T6 (T4 and O on request) |
| Finish | Mill finish; anodized, powder coated, wood-grain, or electrophoresis on request |
| Standards | ASTM B221, EN 755, GB/T 6892 |
| Certification | EN 10204 3.1 MTC; 3.2 and third-party inspection on request |
| MOQ | Flexible; small trial orders accepted |
| Lead time | 15–30 days |
| Trade terms | FOB / CIF; payment by T/T or L/C |
| Port of shipment | Qingdao / Tianjin / Shanghai (or per request) |


Indicative weight per meter for equal angles, calculated from section geometry at 2.70 g/cm³:
| Equal size (mm) | Thickness (mm) | Weight (kg/m, approx.) |
|---|---|---|
| 25 × 25 | 3 | 0.38 |
| 40 × 40 | 4 | 0.82 |
| 50 × 50 | 5 | 1.28 |
| 75 × 75 | 6 | 2.31 |
| 100 × 100 | 8 | 4.13 |
Applications of 6063 T6 Aluminum Angle
Architecture and building: window and door frames, curtain-wall trims, cladding edges, handrails and balustrades.
Display and shop fitting: shelves, racks, frames, and showcases.
Solar and renewable energy: panel mounting frames and support structures.
Transport and vehicle bodies: light structural framing, interior trims, and brackets.
General fabrication: machine guards, fixtures, brackets, and electrical enclosure framing.
Furniture and decoration: frame corners, edge trim, and ornamental profiles.
Inspection and Testing of 6063 T6 Aluminum Angle
Each 6063 T6 aluminum angle order is checked at the mill before dispatch. Routine checks and the records on the mill test certificate include:
| Check | Method / standard |
|---|---|
| Chemical composition | Verified by optical emission spectrometry (OES); assessed against ASTM B221 / EN 573-3. |
| Mechanical properties | Tensile and yield strength, elongation tested per ASTM E8 / EN ISO 6892 on representative samples. |
| Dimensions & shape | Leg length, thickness, angle (90°), straightness, and twist measured per ASTM B221 / EN 755. |
| Surface condition | Visual inspection for cracks, seams, and handling marks on the extruded surface. |
| Mill certificate | Each order ships with EN 10204 3.1 MTC covering chemistry and mechanical results. |
On request, GNEE can arrange EN 10204 3.2 certification and third-party inspection by SGS, BV, or TÜV.



Packaging of 6063 T6 Aluminum Angle
6063 T6 aluminum angle is packed for long-distance sea and land transport to protect the surface and edges from moisture and mechanical damage.
Each piece wrapped with protective PE film; bundles separated by kraft or interleaving paper.
Edge protectors fitted to avoid handling damage at the corners.
Bundle secured on a strong wooden pallet or in a wooden case with steel strapping.
For anodized or powder-coated finishes, extra separation is added to prevent surface rubbing.
Each bundle is labelled with grade, temper, dimensions, heat/lot number, applicable standard, and gross/net weight, and supplied with a packing list to support customs clearance.

About GNEE
GNEE has supplied aluminum mill products to customers in 100+ countries and regions since 2008.
Common 6063 angle sizes and tempers are kept in stock for quick response to both trial and volume orders.
Minimum order quantity is flexible, and both small and large orders are handled.
Material ships with EN 10204 3.1 MTC; 3.2 certification and third-party inspection can be arranged.
A technical team helps match alloy, temper, and standard to the actual working condition.
Processing Services for 6063 T6 Aluminum Angle
GNEE can supply 6063 T6 aluminum angle with added processing so the section arrives closer to your finished part. Available services include:
Cutting: cut-to-length, miter cutting, and sawing to your required dimensions.
CNC machining: drilling, milling, and routing for holes, slots, and notches per drawing.
Punching: standard or custom hole patterns for fixing and assembly.
Chamfering and deburring: edge preparation and burr removal for safe handling and fitting.
Welding and assembly: TIG/MIG fabrication using 4043 or 5356 filler for frames and brackets.
Surface treatment: anodizing, powder coating, wood-grain, and electrophoresis on request.
Processing is quoted per your drawing and quantity. Send the required leg size, thickness, length, tolerance, and finish, and GNEE will confirm feasibility, lead time, and price together with the base angle.

Ordering 6063 T6 Aluminum Angle
MOQ: flexible - small trial orders and full production runs are both handled.
Lead time: 15–30 days for standard items; confirm for special sizes or finishes.
Trade terms: FOB / CIF; payment by T/T or L/C.
Certification: each order ships with EN 10204 3.1 MTC; 3.2 and third-party inspection on request.
Standards: supply to ASTM B221, EN 755, or GB/T 6892 as required.
Send your 6063 T6 aluminum angle requirements-equal or unequal type, leg size, thickness, length, quantity, finish, and destination port-to GNEE for a quote. Our team will confirm stock, lead time, and the applicable standard, then return a quotation with full specifications and the mill test certificate.
FAQ
Q: What is the difference between 6063-T5 and 6063-T6 aluminum angle?
A: Both are extruded; T6 is solution heat-treated and aged, giving higher strength (tensile ≥ 241 MPa vs ≥ 152 MPa for T5). T5 is the lower-cost standard temper for most architectural profiles. Choose T6 where the section carries load.
Q: Can 6063 T6 aluminum angle be welded?
A: Yes. It welds well with TIG/MIG using 4043 or 5356 filler. After welding, strength recovers well on heat-treated tempers, though the heat-affected zone is softer than the base metal.
Q: Which finishes are available?
A: Mill finish as standard, plus anodizing, powder coating, wood-grain, and electrophoresis on request. 6063 responds very well to anodizing.
Q: What sizes can GNEE supply?
A: Equal angles from 20 × 20 mm to 150 × 150 mm and unequal angles up to about 150 × 100 mm, thickness 2–12 mm, in 3 m / 6 m standard lengths or cut to your requirement.
Q: What is the MOQ and lead time?
A: MOQ is flexible and small trial orders are accepted. Standard lead time is 15–30 days; confirm for special sizes or finishes.
Hot Tags: 6063 T6 Aluminium Angle Bar, China 6063 T6 Aluminium Angle Bar manufacturers, aluminium extruded sections, Aluminium L Angle, extruded aluminium sections, Aluminum Angle Extrusions
You Might Also Like
Send Inquiry














