Aluminum foil has moved from a packaging staple to a strategic material inside the new energy chain. As electric vehicle output and grid scale storage capacity expand, the thin gauge foil used as a cathode current collector has become one of the fastest growing segments of the Chinese aluminum foil industry. Rolling mills that once served only food wrapping and air conditioning fins now allocate whole lines to battery foil, and the product mix of the sector has changed accordingly.
Why Battery Foil Became the Growth Engine
Traditional consumption of aluminum foil sits in packaging, construction, air conditioning and household applications. On the industrial side, air conditioning foil, battery foil and electronic foil are the recognised application areas, while thick foil, single zero foil and double zero foil describe the gauge families. Packaging remains the largest single market, covering food, beverages and pharmaceutical products, and thick foil still feeds the production of aluminum tableware and cookware.
What has changed is the balance between these end uses. New energy vehicles and stationary storage systems have pushed demand for lithium battery foil far above the average growth rate of the other segments, so capacity that would previously have gone into packaging grades is now being redirected. This shift is not only a volume story; it also raises the technical bar, because a battery current collector is a functional component rather than a barrier wrapper.
Foil Grades and Tempers Used in Battery Cells
| Alloy | Typical Temper | Role in the Cell | Notes |
|---|---|---|---|
| 1060 | O / H18 | General purpose foil | Commercial purity family, most economical |
| 1070 | O | Cathode current collector | Higher purity and conductivity |
| 1235 | O | Cathode current collector | Widely used battery foil base |
| 1100 | O / H18 | Cathode and general use | Al-Mn family with moderate strength |
| 8079 | O | Cathode current collector | Fine grain structure, uniform surface |
| 8021 | O | Pouch and soft pack parts | Al-Fe-Mn alloy with good barrier behaviour |
| 3003 | H18 | Housing and structural parts | Manganese alloy, higher strength |
Gauge, Width and Surface Requirements
Gauge: industrial aluminum foil covers roughly 0.005 mm to 0.2 mm, while packaging foil usually falls between 0.007 mm and 0.1 mm. Battery current collectors sit at the thin end of the industrial range, commonly between about 0.009 mm and 0.020 mm.
Width: mill production capability is a key selection factor. Foil produced on the continuous belt route can reach a minimum thickness of about 0.0025 mm and a maximum width of around 1800 mm, which allows wider battery electrodes to be coated with fewer splices.
Surface: uniform wettability, absence of roll marks, controlled residual oil and a low pinhole count matter more for battery foil than for packaging foil, because coating defects translate directly into cell scrap.
Mechanics: the foil must combine enough tensile strength to survive high speed coating with enough elongation and ductility to avoid edge cracking during winding.
Geometry: flatness, burr free slit edges and consistent coil diameter support automated unwinding on the customer line.
From Cold Rolled Coil to Double Zero Foil
The production route starts with aluminum foil blanks taken from cold rolled aluminum coils. These blanks are generally pre-annealed between 340 and 480 degrees Celsius and supplied at a thickness of 0.4 mm to 0.7 mm. Aluminum foil rolling is a roll gap free process in which the work rolls remain in an elastic flattened state, so the outgoing gauge is governed by rolling force, rolling speed and strip tension rather than by a fixed gap.
In rough rolling the rolling force is the main control lever for thickness. In finish rolling the foil becomes thinner as rolling speed increases, and higher tension also reduces thickness; to avoid strip breakage, tension is normally selected in the range of 0.2 to 0.4 of the conditional yield strength of the material, denoted as sigma 0.2. The deformation rate of each pass is around 50 percent, and the total deformation rate can exceed 95 percent. Foil with a finished thickness below 0.01 mm to 0.02 mm is rolled in packs, which means double rolling of two layers at the same time followed by separation.
Process Control That Decides Final Quality
Lubrication: thick oil or thin oil is blended into the lubricant to fine tune the effective rolling thickness, and lubricant chemistry has a decisive influence on surface cleanliness.
Roll condition: roll roughness, crown and cleanliness are transferred to the foil surface, so roll change intervals must match the target application.
Annealing: softening treatment controls temper, grain size and the mechanical balance needed by the coating line.
Slitting and winding: tension control during slitting keeps edges burr free and stabilises the coil build.
Quality Checks Buyers Should Agree On
Chemical composition of each heat, checked against the applicable standard for the ordered alloy.
Gauge measurement across the full width, with an agreed tolerance band and sampling frequency.
Tensile strength, elongation and hardness for the required temper.
Surface wettability and residual oil, assessed on defined bench tests.
Pinhole count and visual surface class.
Coil geometry: width, inner diameter, outer diameter, flatness and edge quality.
Traceability from heat number to delivered coil, and packaging suitable for long distance transport.
Frequently Asked Questions
Q: What thickness is used for lithium battery aluminum foil?
Cathode current collector foil is commonly supplied between about 0.009 mm and 0.020 mm, with thinner gauges favoured as cell energy density targets increase.
Q: Which aluminum alloy is most common for battery foil?
1235 and 8079 in the soft O temper are the most widely used, while 1060, 1070 and 1100 also appear depending on conductivity and cost requirements.
Q: What is the difference between single zero foil and double zero foil?
Single zero foil covers gauges from about 0.01 mm up to 0.1 mm, while double zero foil is thinner than 0.01 mm and requires pack rolling to be produced reliably.
Q: Why is double rolling necessary?
Below a finished thickness of roughly 0.01 mm to 0.02 mm a single strip cannot be rolled without instability, so two layers are rolled together and then separated to keep gauge control and reduce breakage.
Q: What tension is used during finish rolling?
Tension is normally set between 0.2 and 0.4 of the conditional yield strength sigma 0.2, balancing thickness reduction against the risk of strip breakage.
Q: How is rolling thickness controlled?
Rough rolling relies mainly on rolling force, while finish rolling adjusts speed and tension; lubrication with thick oil or thin oil provides the final fine adjustment.





