Jul 02, 2025 Leave a message

CNC Cutting Aluminum Parts: Materials and Finish

Service Scope and Material Selection

Custom CNC cutting of aluminium parts covers the conversion of aluminium sheet, plate and extruded stock into finished components through laser cutting, waterjet cutting, routing, milling and turning, followed by deburring and surface treatment. Material selection drives every downstream decision, and the practical range for machined parts spans 6061, 6063, 6082, 6060, 5052, 5083, 2017, 2024, 7050 and 7075, each available as sheet, plate or extrusion from stock held to ASTM B209, ASTM B221 and EN 573-3 composition requirements. Alloy 6061 is the default choice for general machined parts because it combines good strength, weldability and anodising response; 6082 is used where slightly higher strength is needed in thick sections; 5052 and 5083 provide corrosion resistance for marine and fluid-handling parts; 2017 and 2024 deliver high strength and fatigue resistance for stressed parts; and 7050 and 7075 are selected for the highest strength applications where machining, not welding, will join the part.

Cutting and Machining Capability

Process Typical capability Best suited to
Fibre laser cutting Sheet from 0.5 mm to 12 mm, kerf and edge quality per agreed drawing tolerance Fast contours and hole patterns in thin and medium sheet
Waterjet cutting Plate to 100 mm and beyond, no heat-affected zone Thick plate, heat-sensitive alloys, near-net blanks
CNC milling, 3 to 4 axis Dimensional tolerance generally within ISO 2768-m or tighter on request Pockets, profiles, bores and contoured faces
CNC turning Bushes, spacers, insert bodies and rotational parts Parts requiring concentricity and thread forms
Deburring and edge finishing Radius 0.3–0.5 mm nominal, burr-free handling edges All parts before anodising or assembly

Drawings are interpreted to ISO 2768 for general tolerances or to ASME Y14.5 when geometric dimensioning and tolerancing is specified. Thin walls, deep pockets and long slender parts require clamping and tooling strategy agreed before production, because aluminium deflects easily and tool marks or chatter are difficult to remove later.

Surface Treatment Options

Mechanical finishes include sandblasting, bead blasting, brushing, polishing and vibratory finishing, and they set the texture that anodising or coating will reveal. Chemical conversion coating to MIL-DTL-5541 Type I or Type II provides a conductive or paint-base layer, widely used on electronic housings and connector parts. Anodising is the most common protective finish and has three practical forms: Type I chromic acid anodising, which gives a thin but durable film often used for welded assemblies and as a paint primer; Type II sulfuric acid anodising, harder than Type I and widely used on hardware, handles and hydraulic components; and Type III hard anodising, the thickest and hardest film, applied to automotive, aerospace, heavy equipment, marine and defence parts subject to wear. Anodic film thickness is typically in the range of 5–25 µm for Type II and 25–50 µm for Type III, measured with an eddy-current gauge to ISO 2360 against ASTM B580 or MIL-A-8625 requirements. Powder coating is used for coloured, abrasion-resistant surfaces, and electroless nickel plating to ASTM B733 provides a hard, conductive and corrosion-resistant layer for wear surfaces and EMI shielding.

Sheet Metal Fabrication and Assembly

Cut parts are frequently combined with press-brake bending, counter-sinking, tapping, hardware insertion, welding and riveting to produce complete assemblies. Bend allowances should be agreed with reference to the measured inside radius and sheet thickness so that flat patterns nest correctly, and hole-to-bend distances must respect the minimum for the tooling used. Self-clinching fasteners and helical inserts are preferred over tapped threads in thin aluminium, and welded assemblies should use the alloy and filler combination agreed in the drawing notes, with the softened heat-affected zone considered in the design. Assembly-level inspection includes checking flatness after welding, verifying hole positions against the datum scheme, and confirming that any post-weld finishing has not been applied before weld inspection is complete.

Quality Control and Documentation

Control starts with material certification: each heat of aluminium should be traceable through a mill certificate that records alloy, temper, dimensions and mechanical results, with composition checked against ASTM B209 or ASTM B221. In-process inspection uses first-article inspection against the drawing, with calipers, micrometers, height gauges and coordinate measuring machines recording the dimensions that the drawing identifies as critical. Finished part records typically include dimensional reports, anodic film thickness readings, coating adhesion results by cross-hatch and tape test, salt spray results to ASTM B117 where specified, and hardness or conductivity checks for alloys whose heat treatment condition must be verified, since conductivity testing detects whether a 7075 or 2024 part was correctly aged. Packaging must protect machined and anodised surfaces with film or interleaving, and part marking should use a method that survives shipping without damaging the finish.

Frequently Asked Questions

Q: Which aluminium alloy is best for general CNC machining?

A: 6061, because it machines cleanly, welds well, anodises to a good finish and offers a reliable balance of strength and cost.

Q: What tolerances can machined aluminium parts hold?

A: General tolerances to ISO 2768-m are routine, with tighter values achievable for critical features when the drawing and datum scheme support them.

Q: What is the difference between Type II and Type III anodising?

A: Type II sulfuric anodising produces a film typically 5–25 µm thick, while Type III hard anodising produces a thicker and harder film, commonly 25–50 µm, for wear resistance.

Q: Can anodised parts be welded afterwards?

A: No; welding destroys the anodic film locally, so welding and mechanical finishing must be completed before anodising.

Q: How is anodic film thickness verified?

A: With an eddy-current gauge to ISO 2360, evaluated against ASTM B580 or MIL-A-8625 acceptance criteria.

Q: Which documents should accompany machined parts?

A: Material certificates with heat traceability, a dimensional inspection report, and finish test records such as film thickness and coating adhesion results.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry