Aug 20, 2025 Leave a message

5083 H321 Marine Grade Aluminum Plate: Properties, Standards and Applications

5083 H321 is the plate grade that naval architects reach for when a structure has to survive salt water, welding and fatigue at the same time. The alloy is an Al-Mg material carrying 4.0 to 4.9 percent magnesium, and H321 is a strain hardened and stabilised temper supplied to ASTM B209 for marine and offshore work. Knowing what the designation actually guarantees makes specification and fabrication far more predictable.

What the H321 Designation Means

The H designation covers strain hardened tempers. The first digit shows that the product has been strain hardened only, and the following digits record how far the cold reduction went and what thermal treatment followed. In H321 the metal is cold worked to approximately the quarter hard level and then stabilised, which is a low temperature conditioning treatment rather than an ageing treatment. The result is a plate that keeps its strength and its corrosion resistance after years of exposure, instead of continuing to change in service.

H321 should not be confused with H116. Both are marine tempers and both are stabilised, but H116 carries an additional requirement for resistance to intergranular corrosion after a sensitisation exposure, which makes it the usual choice for welded hull structures and for applications where the plate will see elevated temperature during fabrication.

Chemical Composition and Applicable Standards

5083 is a non-heat-treatable alloy and its properties come from solid solution strengthening by magnesium, supported by manganese and chromium additions that control grain structure. Typical composition limits are shown below.

Element Content, % by weight
Magnesium 4.0 - 4.9
Manganese 0.40 - 1.0
Chromium 0.05 - 0.25
Iron 0.40 max
Silicon 0.40 max
Zinc 0.25 max
Copper 0.10 max
Titanium 0.15 max

Plate in this temper is ordered to ASTM B209, with dimensional tolerances and flatness requirements set by the same specification. Where the material is used under pressure rules, additional requirements for tensile testing and for corrosion testing apply, and the stabilised tempers are the ones normally accepted.

Mechanical and Physical Properties

Typical minimum values for 5083 H321 plate of 6.35 to 38 mm thickness are given in the table. Thinner and thicker sections can differ, and the mill certificate for the actual heat should always be checked against the purchase order.

Property Value
Tensile strength 305 MPa minimum
Yield strength, 0.2 percent offset 215 MPa minimum
Elongation in 50 mm 12 percent minimum
Density 2.66 g/cm3
Elastic modulus 71 GPa
Melting range 585 - 638 C

The strength to weight ratio is the reason the grade dominates light marine structures. A 5083 H321 plate delivers roughly 115 megapascals of yield strength per unit of density, which lets designers cut structural weight by around one half compared with mild steel at equal stiffness when the section is redesigned for the lower modulus.

Welding and Fabrication

5083 is one of the most weldable high strength aluminium alloys and is normally joined by MIG or TIG using 5183 or 5356 filler wire. The weld pool is fluid and penetration is good, so full fusion joints are achievable in a single pass on thin plate. Two points deserve attention during fabrication.

Heat affected zone softening: the thermal cycle partially anneals the parent metal next to the weld, so the zone is weaker than the unaffected plate. Joint design should therefore place the weld away from the points of highest stress.

Filler selection: fillers containing more than three percent magnesium, such as 5356 and 5183, are not intended for prolonged service above about 65 degrees Celsius, which matches the service limit of the parent plate.

Forming is straightforward in the as-supplied condition. Cold bending radii of about two to three times the plate thickness are practical for the annealed temper and rather more generous for H321, and hot forming should be avoided because it can alter the stabilised structure.

Marine and Offshore Applications

The grade is used for hull plating, decks, bulkheads, superstructures and tank structures on workboats, ferries, fishing vessels and yachts. Offshore it appears in helidecks, walkways, accommodation modules and secondary structure, where low weight reduces the load on the platform, and onshore it is found in road tankers, silos and cryogenic insulation panels where toughness at low temperature is valuable.

Because the alloy does not become brittle at low temperature, it retains useful toughness down to cryogenic conditions, which is why it is also specified for liquefied gas containment and for cold box structures. Its surface needs no painting to survive a marine atmosphere, although coatings are often applied for appearance or for antifouling reasons rather than for corrosion control.

Corrosion Behaviour and Service Limits

Resistance to seawater is excellent. The metal forms a stable oxide film that repairs itself when damaged, and the magnesium rich chemistry resists both general and pitting attack in chloride environments. In the stabilised tempers, resistance to intergranular corrosion is maintained even after sustained exposure at moderately elevated temperature, which is the property that matters most in welded structures that must remain in service for decades.

Two limits apply. Contact with steel or stainless steel fasteners should be managed by insulation or by a suitable barrier, since the aluminium will act as the anode in a galvanic couple. And continuous service above roughly 65 degrees Celsius should be avoided, because prolonged exposure at higher temperature allows magnesium to segregate to grain boundaries and reduces corrosion resistance.

Frequently Asked Questions

Q: What does the H321 temper mean?
The metal is strain hardened to about the quarter hard level and then stabilised, so the temper is thermally conditioned rather than aged.

Q: What is the difference between 5083 H116 and H321?
Both are stabilised marine tempers, but H116 adds a requirement for intergranular corrosion resistance after sensitisation testing, which suits welded hull structures.

Q: Can 5083 H321 be welded without losing strength?
The heat affected zone is partially annealed and therefore softer than the parent plate. Joints should be designed so that welds sit away from peak stress locations.

Q: Is painting required for marine service?
No. The alloy resists seawater without coating, although paint is often applied for appearance or antifouling rather than for corrosion protection.

Q: What filler wire should be used?
5183 or 5356 filler is normal practice. Fillers with more than three percent magnesium are not intended for sustained service above about 65 degrees Celsius.

Q: Does 5083 H321 perform at low temperature?
Yes. The alloy keeps useful toughness at cryogenic temperature, which is why it is used for liquefied gas containment and cold box structures.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry