What Makes 7075 an Ultra-High-Strength Alloy
7075 aluminum plate belongs to the Al-Zn-Mg-Cu series of ultra-high-strength alloys. Its strength comes from a balanced chemical composition combined with precise heat treatment. Zinc is the dominant strengthening element: together with magnesium and copper it forms intermetallic phases such as MgZn2 and Al2CuMg, which after solution heat treatment and aging are finely and uniformly dispersed in the aluminum matrix. A controlled chromium addition refines the grain structure, which supports both mechanical performance and corrosion resistance. Composition for the alloy is fixed by standards such as GB/T 3190, while plate and sheet properties and tolerances are governed by ASTM B209.
The alloy is characterised by a high yield ratio - yield strength close to tensile strength - and an excellent strength-to-weight ratio. Properties are stable at room temperature and up to about 120 degC, but ductility is relatively low and high-temperature strength falls off, so the temper must be chosen to balance strength against plasticity. T6 and T651 are the two most widely used conditions.
Core Mechanical Properties: 7075-T6 versus 7075-T651
The differences between the two tempers come from small variations in the heat treatment route. The comparison below is based on 1-10 mm sheet thickness, a common commercial range, and reflects the values quoted with reference to GB/T 3190 and ASTM B209 together with routine testing data.
| Property | 7075-T6 | 7075-T651 |
|---|---|---|
| Tensile strength, Rm | not less than 540 MPa | not less than 550 MPa |
| 0.2 percent proof stress, Rp0.2 | not less than 480 MPa | not less than 485 MPa |
| Elongation after fracture, A | not less than 8 percent | not less than 6 percent |
| Hardness | 145-150 HBW | 150-155 HBW |
| Elastic modulus, E | 71 GPa | 71 GPa |
| Fatigue strength | about 155 MPa | about 175 MPa |
| Stress corrosion cracking resistance | Moderate | Excellent |
Tensile strength. T651 is slightly stronger, mainly because pre-stretching refines the precipitate distribution.
Yield strength. The two tempers are very close, but T651 holds its yield strength more consistently, which suits large precision parts.
Elongation. T6 is the more ductile of the two; T651 gives up some elongation because of the stress-relief stretch.
Hardness. Overall levels are comparable, and the real advantage of T651 is a more uniform hardness distribution, which reduces the risk of local soft or hard spots during machining.
Elastic modulus. Identical, because both are the same alloy system, so elastic behaviour under load is the same.
Fatigue and stress corrosion. Lower residual stress gives T651 clearly better fatigue performance and resistance to stress corrosion cracking, which matters in humid, marine and salt-spray service.
How Pre-Stretching Changes T651 Behaviour
T651 is essentially T6 followed by controlled stretching and aging, a route that relieves internal stress rather than changing the alloy. That is why modulus and chemistry-based properties stay the same while fatigue life, dimensional stability and stress corrosion performance improve. For thick plate that will be machined heavily, this stability is often the deciding factor: a plate with lower residual stress distorts less when material is removed and keeps its flatness after machining.
Thickness Effect on Strength
Property levels are thickness dependent. Above 10 mm, both tempers show a slight reduction in strength; for plate in the 10-50 mm range tensile strength is typically quoted at not less than 530 MPa, with the relative ranking of T6 and T651 unchanged. Above roughly 50 mm, special rolling and heat treatment practice is needed and the drop in strength becomes more noticeable. When specifying, always take the minimum from the governing standard for the actual thickness rather than assuming a single figure covers all sizes.
Selecting and Machining the Right Temper
Choose 7075-T6 where maximum ductility and slightly better formability are needed, or where the part is thin and residual stress is not a concern.
Choose 7075-T651 for thick, heavily machined structural plate, for parts exposed to cyclic loading, and for humid, marine or salt-spray environments.
Both tempers should be machined with sharp tooling at controlled feeds, since the high yield ratio leaves little margin for work hardening at the cut edge.
Do not use either temper for continuous service much above 120 degC, where strength falls off.
Cladding, anodising or chromate conversion coating can be applied, but process selection must account for the copper content of the alloy.
Frequently Asked Questions
Q: Is 7075-T651 stronger than 7075-T6?
Yes, marginally. Tensile strength is typically quoted at not less than 550 MPa for T651 against 540 MPa for T6, and hardness is slightly higher. The important differences, however, are fatigue life, stress corrosion resistance and dimensional stability rather than raw strength.
Q: Why is 7075-T651 fatigue strength higher?
Because the pre-stretching step reduces residual stress in the plate. Lower internal stress means crack initiation under cyclic loading is delayed, which is why T651 is preferred for structural parts under repeated loading.
Q: Which temper has better elongation?
7075-T6, with not less than 8 percent elongation after fracture against not less than 6 percent for T651. The stress-relief stretch applied to T651 costs some ductility.
Q: Does the elastic modulus differ between T6 and T651?
No. Both conditions are the same alloy system, so the elastic modulus is 71 GPa for each, and elastic deflection under a given load is identical.
Q: How does thickness affect these properties?
Strength falls slightly as thickness increases. In the 10-50 mm range tensile strength is commonly quoted at not less than 530 MPa, and above about 50 mm special processing is required with a more noticeable reduction.
Q: Is 7075-T651 suitable for marine service?
Its resistance to stress corrosion cracking is excellent, which makes it far more suitable than T6 in humid, marine and salt-spray conditions, although the alloy still needs suitable protection on exposed surfaces.





