Nov 18, 2025 Leave a message

What-is-5052-H114-Aluminum-Tread-Plate.pdf

5052 H114 Aluminum Tread Plate: Five-Bar Anti-Slip Checker Sheet for Decks and Floors

What Is 5052 H114 Aluminum Tread Plate?

5052 H114 aluminum tread plate is a five-bar patterned sheet produced from the 5052 aluminium-magnesium alloy. The pattern is rolled into the plate before the final pass, so the raised bars are integral to the sheet rather than applied afterwards, and the plate keeps its anti-slip performance for the whole service life. Five-bar tread plate in 5052 is one of the most widely stocked anti-slip aluminium products, which means stable quality, short lead times and competitive pricing.

5052 belongs to the Al-Mg series and offers medium strength, excellent corrosion resistance, good weldability and easy forming. It cannot be strengthened by heat treatment, so its properties are set by the temper and by the amount of cold work in the sheet. H114 is a strain hardened and partially annealed temper that keeps the pattern sharp while leaving enough ductility for bending, brake forming and light drawing.

Why Choose 5052 H114 for Anti-Slip Surfaces

Five-bar pattern – raised bars run at an angle to the sheet edges so that foot traffic always crosses a grip edge; the pattern also drains water and limits standing film on the surface.

Corrosion resistance – magnesium in solid solution gives good resistance to salt spray, humid heat and road salt, so the plate does not rust the way steel tread plate does.

Fatigue and toughness – 5052 resists cracking under repeated loading and impact, which suits vehicle floors, ramps and trailer decks.

Formability and welding – the plate can be bent over tight radii and welded with 5052 or 5356 filler for leak-tight joints on tanks and enclosures.

Appearance – a bright mill finish needs no painting, and anodizing further extends service life and gives a uniform decorative surface.

Alloys, Tempers and Size Range

Item Range
Typical alloys 5052, 5754
Temper O, H32, H111, H114
Thickness 1.2 / 1.5 / 2.0 / 2.5 / 3.0 / 3.5 / 4.0 / 5.0 / 6.0 mm in stock, up to 10.0 mm on request
Standard sheet size 1220 × 2440 mm
Custom width Up to 1900 mm
Custom length Up to 12000 mm

Standard sheets are held in stock and can be supplied in split packs or cut to size. Custom widths and long lengths are produced to order, which suits ship decking, bus flooring and long vehicle ramps where few joints are wanted.

Typical Applications

Anti-slip flooring and pedal surfaces – the primary use of 5052 tread plate, providing grip on walkways, platforms and machine steps.

Automotive footboards – bus and coach entry steps and footwell plates that must resist road salt and repeated foot traffic.

Cold storage floors – the plate tolerates low temperature and moisture without becoming brittle and stays safe in wet conditions.

Ship decks and gangways – 5052 keeps its surface in salt spray, so it is widely used on vessels, yachts and other saline environments.

Storage tanks, vessels and welded structures – where formability, weldability and moderate static strength are required together.

Service Behaviour and Maintenance

The pattern stays visible after years of use because the bars are rolled rather than painted or coated, and the aluminium oxide layer that forms naturally protects the surface against oxidation. Cleaning is simple: the smooth parts of the surface do not hold dirt, and a wipe with neutral detergent restores the finish. Unlike steel tread plate, 5052 does not rust, so no repainting cycle is needed and the plate keeps a consistent bright appearance.

Where a longer service life or a decorative finish is required, the sheet can be anodized. Anodizing thickens the natural oxide layer on the pattern and on the land area at the same time, so grip and appearance are both preserved. 5052 also machines and drills readily for handrails, hatch frames and mounting brackets.

Ordering and Quality Control

Melt chemistry verified by spectrographic analysis before casting, with certificates issued with each shipment.

Thickness, width and diagonal dimensions inspected on every sheet to keep assemblies square.

Pattern height and bar coverage checked so that grip performance stays consistent between batches.

Sheets protected with a removable film and shipped on wooden pallets with moisture protection.

Frequently Asked Questions

Q: What does the H114 temper mean?
H114 is a strain hardened and partially annealed temper; it keeps the rolled five-bar pattern sharp while leaving enough ductility for bending and brake forming.

Q: Which thicknesses are available from stock?
Standard 1220 × 2440 mm sheets are held in 1.2, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 5.0 and 6.0 mm, with other thicknesses up to 10 mm available to order.

Q: Is 5052 tread plate suitable for ship decks?
Yes. The alloy resists salt spray and humid conditions, which is why 5052 and 5754 tread plate are regularly used on decks, gangways and skid plates.

Q: Can the tread plate be anodized?
Yes. Anodizing thickens the oxide layer on both the bars and the land area, extending service life and giving a uniform colour, and the anti-slip effect is retained.

Q: How does it compare with steel tread plate?
Aluminium tread plate is about one third the weight of steel, will not rust, needs no painting and is easier to cut and drill, although it is not intended for the highest wear duties.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry