Nov 30, 2025 Leave a message

6061 T5 vs T6 Aluminum Alloy Bar: Temper, Properties and Selection

What Is a 6061 Aluminum Alloy Bar

6061 aluminum bar is a solid section produced from a heat-treatable aluminium-magnesium-silicon alloy by hot extrusion or cold finishing. Magnesium and silicon combine to form the Mg2Si strengthening phase, a small copper addition raises the response to precipitation hardening, and chromium controls grain structure. The result is a medium-strength alloy with good corrosion resistance, weldability and machinability, supplied as round bar, square bar, flat bar, rectangular bar and hexagonal bar.

The nominal composition under ASTM B221 is Mg 0.8-1.2%, Si 0.40-0.8%, Cu 0.15-0.40%, Cr 0.04-0.35%, Fe 0.7% max, Mn 0.15% max, Zn 0.25% max and Ti 0.15% max, balance aluminium. GB/T 3190 lists the same ranges, so material sourced to either system is equivalent once the temper and the mechanical property requirements are matched.

T5 vs T6: How the Temper Route Changes Performance

Both tempers start from the same chemistry. The difference is what happens after the bar leaves the press. T5 material is cooled at the press and then artificially aged; T6 material is given a separate solution heat treatment and a controlled aging cycle before delivery. That extra step is the reason the two tempers behave so differently in service.

Temper Production route Typical tensile strength Typical yield strength Best suited to
6061-T5 Press-quenched, then artificially aged About 241 MPa (35 ksi) About 207 MPa (30 ksi) Extruded sections needing a clean finish and moderate loads
6061-T6 Solution heat treated, then artificially aged 262 MPa (38 ksi) minimum per ASTM B221; about 310 MPa (45 ksi) typical 241 MPa (35 ksi) minimum per ASTM B221; about 276 MPa (40 ksi) typical Machine parts, structural brackets, load-bearing components

T5 therefore sits below T6, not above it. Because T5 skips the separate solution treatment, it offers faster extrusion, less distortion and a smoother as-extruded surface, but it cannot reach the T6 strength level. The 290 MPa (42 ksi) tensile figure sometimes quoted for T6 belongs to plate under ASTM B209, not to extruded bar, and should not be used as a bar acceptance value.

Mechanical Properties and Referenced Standards

Bar products are normally ordered against ASTM B221 for extruded rod and bar, ASTM B211 for rolled and cold-finished bar, GB/T 3191 for extruded bar and tube, or GB/T 3190 for composition. Where a project calls for a temper beyond the two standard conditions, T4, T451, T651 and T6511 are also produced, with T6511 applying to extruded bar that is stretched and aged.

Property 6061-T5 6061-T6
Tensile strength About 241 MPa (35 ksi) 262 MPa (38 ksi) minimum; about 310 MPa (45 ksi) typical
Yield strength (0.2% offset) About 207 MPa (30 ksi) 241 MPa (35 ksi) minimum; about 276 MPa (40 ksi) typical
Elongation Around 12% in common diameters 8-12% depending on section and thickness
Hardness About 60-70 HB About 95-100 HB
Density 2.70 g/cm3 2.70 g/cm3
Melting range 582-652 C 582-652 C
Thermal conductivity About 167 W/(m.K) About 167 W/(m.K) at 25 C

Available Shapes, Sizes and Surface Finishes

Forms: round bar and rod, square bar, flat bar, rectangular bar, hexagonal bar, plus custom profiles.

Diameter or width: 5 mm to 600 mm for round and square sections; flat bar widths from 10 mm to 200 mm with thickness from 2 mm to 200 mm.

Length: 1 m to 6 m standard, cut to fixed lengths on request.

Production route: hot extruded, cold drawn (fine drawn), or cut from plate for heavy flat sections.

Surface: mill finish, bright, polished, anodised, powder coated, electrophoresis or wood-grain transfer.

Secondary operations: CNC turning and milling, drilling, sawing, bending, welding and assembly.

Typical Applications Across Industries

Automotive and transport: brackets, seat frames, chassis spacers, busbar supports and other components where weight reduction matters.

Aerospace and defence: non-critical fittings, jigs and ground support equipment that benefit from a high strength-to-weight ratio.

Construction: curtain wall mullions, handrails, window and door frames, structural connectors and architectural trim.

Machinery and automation: guide rails, actuator bodies, robot arms, pneumatic manifolds and fixture plates.

Electrical and energy: heat sinks, busbar housings and frames for cabinets and enclosures.

Consumer and industrial equipment: furniture frames, ladders, trolley chassis and food-processing equipment supports.

For a given load case, choose T6 where the part carries the design load and needs stiffness, and T5 where bending or anodising quality matters more than peak strength. Both tempers weld well by TIG and MIG processes, and both can be anodised, although T6 parts are normally machined before surface treatment because anodising thickness affects tight tolerances.

Frequently Asked Questions

Q: Is 6061-T6 stronger than 6061-T5?
Yes. ASTM B221 requires a minimum tensile strength of 262 MPa (38 ksi) and a minimum yield strength of 241 MPa (35 ksi) for 6061-T6 extruded bar, while 6061-T5 typically develops around 241 MPa (35 ksi) tensile and 207 MPa (30 ksi) yield.

Q: Why does the source data sometimes show a higher figure for T5?
Those tables mix product forms. A 42 ksi tensile value belongs to 6061-T6 plate under ASTM B209. Within the same bar product, the T5 temper is always the lower-strength condition.

Q: Can 6061-T6 bar be bent or formed?
Forming is possible in the T4 or T451 condition before aging, and in T6 only with generous bend radii and pre-heating. Cold bending a fully aged T6 bar to a tight radius risks surface cracking, so the bend radius is usually agreed with the supplier before cutting.

Q: Which standards apply to an order for 6061 bar?
Extruded rod and bar follow ASTM B221; rolled or cold-finished bar follows ASTM B211; composition follows ASTM B221 or GB/T 3190; extruded bar and tube made in China commonly follow GB/T 3191. A mill test certificate issued against the ordered standard accompanies each heat.

Q: How does 6061 compare with 6063 for extruded bar?
6063 extrudes faster and anodises to a brighter finish, but its strength is lower because it contains less magnesium and silicon. Choose 6063 for architectural profiles and 6061 for machined or load-bearing bar.

Q: What sizes and tempers are stocked in a typical mill programme?
Round bar from 5 mm to 600 mm, square bar to 200 mm, and flat bar from 10 mm wide, in O, H112, T4, T451, T5, T6, T651 and T6511 tempers, with length tolerance and straightness agreed to the ordered standard.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry