GNEE Aluminum has completed a 30-line 6061-T6 aluminum piping package for a marine and process contractor in the United Arab Emirates: tube in OD 21–27 mm, 45° and 90° long-radius elbows, watertight penetration sleeves and 770 PN-designated flanges, shipped as one consolidated lot with mill test certificates.
The order covers 127.6 m of tube in four sizes, 15 butt-weld elbows, 70 watertight penetration sleeves and 770 flanges across three designations - set-in, set-on and slip-on - and ten PN/DN combinations. Everything is 6061-T6, so the package runs off one alloy, one temper and one certificate set.
UAE Marine and Process Demand for 6061-T6 Aluminum
The UAE market for aluminum piping is driven by three things that all sit on the coast: ship repair and newbuild yards around Dubai and Sharjah, desalination and water treatment plants, and process packages fabricated as skids and installed on site. In all three, aluminum competes with carbon steel and stainless on weight and maintenance, not on first cost.
6061-T6 gets specified when a line has to hold pressure, be machined accurately and still resist the Gulf atmosphere. The T6 temper carries thin flange sections and grooved fittings, and the Mg-Si chemistry stays stable in humid, salt-laden air where painted carbon steel needs re-coating on a cycle.
Buyers here ask for three things before an order: a named standard per line item, a certificate that traces to the heat number, and packing that survives a mixed container.
Customer Technical Requirements for the 6061-T6 Aluminum Package
Specification of the 6061-T6 Aluminum Pipe, Fittings and Flanges
| Line | Item as ordered | Size | Length | Quantity |
|---|---|---|---|---|
| 1 | PIPE | OD 27 × wall 5 mm | 2900 mm | 31.9 m |
| 2 | PIPE | OD 21 × wall 5 mm | 2900 mm | 31.9 m |
| 3 | PIPE | OD 27 × wall 3 mm | 2900 mm | 31.9 m |
| 4 | PIPE | OD 21 × wall 3 mm | 2900 mm | 31.9 m |
| 5 | ELBOW 45° LR | SCH 40 / DN 40 | - | 5 pcs |
| 6 | ELBOW 90° LR | SCH 40 / DN 40 | - | 5 pcs |
| 7 | ELBOW 45° LR | SCH 40 / DN 25 | - | 5 pcs |
| 8 | W.T. PENETRATION SLEEVE | SCH 80 / DN 20 | - | 70 pcs |
| 9 | SET-IN FLANGE | DN 15 / PN 10 | - | 20 pcs |
| 10 | SET-IN FLANGE | DN 20 / PN 10 | - | 35 pcs |
| 11 | SET-IN FLANGE | DN 20 / PN 16 | - | 20 pcs |
| 12 | SET-IN FLANGE | DN 25 / PN 6 | - | 15 pcs |
| 13 | SET-IN FLANGE | DN 32 / PN 10 | - | 15 pcs |
| 14 | SET-IN FLANGE | DN 40 / PN 16 | - | 30 pcs |
| 15 | SET-IN FLANGE | DN 50 / PN 6 | - | 5 pcs |
| 16 | SET-IN FLANGE | DN 65 / PN 16 | - | 25 pcs |
| 17 | SET-ON FLANGE | DN 25 / PN 10 | - | 10 pcs |
| 18 | SET-ON FLANGE | DN 50 / PN 6 | - | 300 pcs |
| 19 | SET-ON FLANGE | DN 65 / PN 6 | - | 15 pcs |
| 20 | SET-ON FLANGE | DN 65 / PN 16 | - | 20 pcs |
| 21 | FLANGE SLIP-ON, FF | DN 15 / PN 10 | - | 30 pcs |
| 22 | FLANGE SLIP-ON, FF | DN 15 / PN 16 | - | 10 pcs |
| 23 | FLANGE SLIP-ON, FF | DN 20 / PN 6 | - | 10 pcs |
| 24 | FLANGE SLIP-ON, FF | DN 20 / PN 10 | - | 10 pcs |
| 25 | FLANGE SLIP-ON, FF | DN 20 / PN 16 | - | 35 pcs |
| 26 | FLANGE SLIP-ON, FF | DN 50 / PN 16 | - | 70 pcs |
| 27 | FLANGE SLIP-ON, FF | DN 50 / PN 40 | - | 25 pcs |
| 28 | FLANGE SLIP-ON, FF | DN 65 / PN 6 | - | 30 pcs |
| 29 | FLANGE SLIP-ON, FF | DN 65 / PN 16 | - | 10 pcs |
| 30 | FLANGE SLIP-ON, FF | DN 80 / PN 10 | - | 30 pcs |
Quantities and designations are as issued on the customer's bill of materials; lines are sorted by item type and nominal size, not by the original line order. Tube is supplied in 2900 mm lengths and the quantity column is total length per size.


Set-in and set-on flange descriptions follow the customer's own naming: the hub, bore and weld preparation for those two were taken from the drawing, while PN and DN fix outside diameter, bolt circle and thickness. Flange dimensions and facing follow the EN 1092 table for the ordered PN and DN.
| Alloy and temper | 6061-T6 (Al-Mg-Si, heat treated and artificially aged) |
|---|---|
| Product forms | Seamless tube, butt-weld elbows, penetration sleeves, PN-designated flanges |
| Tube standard | ASTM B241; metric diameter and wall tolerances checked against EN 755-7 |
| Fitting standard | ASTM B361, dimensions per ASME B16.9 (long radius, 45° and 90°) |
| Flange standard | EN 1092-4, aluminum alloy flanges, PN designated |
| Total flange quantity | 770 pcs across set-in, set-on and slip-on designations |
| Surface | Mill finish, no coating |
| Destination | United Arab Emirates |
| Inspection | EN 10204 3.1 mill test certificate; 3.2 and third-party inspection on request |
Quality Control on the 6061-T6 Aluminum Pipe and Flange Lot
Thirty lines in one lot means thirty chances to mix sizes, and a wrong-size flange is only found at fit-up. Inspection was organised around that risk: verify the alloy once, verify dimensions line by line, then mark each package so the consignee can receive against the bill of materials.
Chemical composition by spectrometer - confirms 6061 chemistry (Mg 0.8–1.2%, Si 0.4–0.8%) so no lookalike 6xxx grade is substituted on a line that reads the same from the outside.
Tensile test per lot - proves T6 rather than O or T4, which matters because flange sections are machined thin and the tube is welded on site.
Tube dimensional check - outside diameter, wall and roundness on every size, so elbows and slip-on bores fit the tube they are paired with.
Fitting dimensional check per ASME B16.9 - centre-to-end, angle, outside diameter and end preparation, which together decide whether the elbow pulls the line out of alignment during welding.
Flange dimensional check per EN 1092-4 - outside diameter, bolt circle, hole count and size, thickness and facing, checked against the PN and DN of that specific line.
Visual and surface inspection - dents, deep scratches and embedded iron from handling, which become corrosion start points in a coastal installation.


Hydrostatic or pneumatic testing is quoted separately where a line is specified for pressure service, and positive material identification can be added for consignments that will be witnessed. Both are agreed at order stage.
Export Packaging for 6061-T6 Aluminum Delivery to the UAE
A 770-piece flange order packed into the same container as 127.6 m of tube is a handling problem before it is a shipping problem. The DN 15 and DN 20 flanges - over 200 pieces between them - are the ones that get lost or bent, so they travel cased by size and PN rather than loose in a mixed carton.
Flanges cased by PN and DNFaces protected with plastic caps, parts stacked face to back, each case marked with the bill-of-materials line number so it can be booked in without opening it.
Tube bundled with capped ends2900 mm lengths bundled by size and wall, ends capped to keep out moisture and grit, bundles strapped and lifted with slings rather than forks.
Wood treated to ISPM 15Heat-treated wood or plywood cases, marked in line with the phytosanitary requirement applied at Gulf ports of entry.
Document set prepared before loadingCommercial invoice, packing list keyed to the same line numbers, bill of lading, certificate of origin and the mill test certificate; chamber or embassy attestation arranged in advance where the letter of credit calls for it.
Loading is photographed before the doors close, and the sequence is planned so flange cases sit on the floor rather than on top of tube bundles. Where a consignee needs material released in a set order at site, the packing list is sequenced to match.
Available Sizes of GNEE Aluminum Pipe, Fittings and Flanges
Beyond the sizes on this order, the ranges below are what we produce as standard for 6061-T6. Anything outside them is quoted to drawing rather than refused.
| Product | Dimension type | Typical range | Tolerance standard |
|---|---|---|---|
| Aluminum tube | Outside diameter | 6 – 300 mm | EN 755-7 / ASTM B241 |
| Aluminum tube | Wall thickness | 0.5 – 30 mm | EN 755-7 |
| Aluminum tube | Length | 1000 – 12000 mm | Cut to length on request |
| Aluminum butt-weld fitting | Nominal size | DN 15 – DN 600 (1/2 – 24 in) | ASME B16.9 / ASTM B361 |
| Aluminum butt-weld fitting | Configuration | 45° / 90° / 180°, long and short radius, tee, reducer, cap | ASME B16.9 |
| Aluminum flange | Nominal size and rating | DN 15 – DN 600, PN 6 – PN 40; higher ratings to drawing | EN 1092-4 |
| Aluminum flange | Face type | Flat face, raised face | EN 1092-4 |
| Watertight penetration sleeve | Size and wall | Made to drawing, heavier wall than the pipe carried | Drawing |
About GNEE Aluminum
GNEE Aluminum has supplied aluminum since 2008 from China, and ships to more than 100 countries and regions. The range covers plate, sheet, coil, foil, bar, tube, extruded profile, fittings and flanges.
Capability relevant to this order: cutting to length, bevel and end preparation, flange machining to PN tables, marking by heat number and line number, and export packing. Drawings are reviewed before a line goes into production rather than after.
FAQ
Q: Which standards apply to this 6061-T6 aluminum piping package?
A: Tube is produced to ASTM B241 with metric diameters and walls checked against EN 755-7, elbows to ASTM B361 with dimensions per ASME B16.9, and flanges are PN-designated to the EN 1092 series, of which EN 1092-4 is the aluminum alloy part. The package is one alloy and one temper, so a single certificate set covers it.
Q: Can 6061-T6 aluminum pipe be welded on site?
A: Yes, 6061 welds with 5356 or 4043 filler, but the heat-affected zone loses the T6 temper. Welded joints are therefore designed on as-welded properties rather than the parent-metal T6 values, and the welding procedure should be qualified for the wall thickness being joined.
Q: What is a watertight penetration sleeve used for?
A: A penetration sleeve is the short section of heavier-wall tube welded through a bulkhead or deck so a pipe run can pass a structural boundary without cutting the structure open. This order used SCH 80 DN 20 sleeves, heavier than the SCH 40 pipe they carry, so the sleeve absorbs the weld and keeps the boundary intact.
Q: Do you supply aluminum pipe and flanges in quantities below these?
A: Yes. MOQ is flexible, so both small trial orders and large-volume orders are accepted. Mixed packages with several sizes on one bill of materials are normal for us, and each line is marked separately so it can be matched to the drawing on site.
Q: How are mixed aluminum piping lots packed for shipment to the Gulf?
A: Lines are bundled or cased by size and PN, flange faces are protected with plastic caps, tube ends are capped, and everything travels on ISPM 15 heat-treated wood or plywood cases. Each package is marked with the line number from the bill of materials, the alloy and temper, and the heat number, so the consignee can receive against the drawing without opening every case.
Ask for a quotation on a mixed 6061-T6 aluminum piping package - send the bill of materials with alloy, temper, PN or schedule callout and quantity per line, and the technical team will come back with sizes resolved line by line and a certificate scope for the lot.
Export destination must comply with applicable export-control and sanctions regulations. GNEE supplies only to eligible end-users and compliant destinations.









