Jul 10, 2023 Leave a message

GNEE Aluminum Foil: Food-Grade, Flexible & Industrial Foil In 1xxx / 3xxx / 8xxx

Stop losing production time to foil that tears, jams, or lets your product spoil. That is what buyers tell us they fear most - uneven gauge that breaks during slitting, pinholes that kill the barrier, and missing compliance papers that block customs or a customer audit. GNEE has exported aluminum foil for 18 years, and we control those exact failure points with checks you can verify, not slogans you have to trust.

 

What you can order

We supply pure and alloy foil across the common commercial families:

1xxx (1050, 1060, 1070, 1100, 1235) - high purity, used for decorative, labeling, and general wrapping.

3xxx (3003) - added strength, common in containers and formed packaging.

8xxx (8011, 8079) - the workhorses for flexible packaging and lamination.

Gauges run from ultra-thin capacitor foil up to ~0.2 mm industrial stock. Exact range and tolerance are confirmed per order.

 

Specification (indicative - confirm against your order)

Alloy

Typical gauge (mm)

Common temper

Standard

Typical use

8011

0.006 – 0.05

O / H22 / H24

ASTM B479 / GB/T 3198

Flexible packaging, lamination

8079

0.006 – 0.05

O

ASTM B479 / GB/T 3198

High-barrier packaging

3003

0.02 – 0.20

O / H14 / H24

ASTM B479 / GB/T 3198

Containers, formed trays

1235

0.006 – 0.02

O

ASTM B479 / GB/T 3198

Capacitor, laminate

1050 / 1060 / 1100

0.02 – 0.20

O / H14 / H24

ASTM B479 / GB/T 3198

Labeling, decoration, general

Gauges and tempers above are indicative and grade-dependent. Final specification is set by your drawing or order.

 

GNEE Aluminum Foil

 

Where it goes (applications)

Food & household - wrapping, freezer-to-oven trays, lidding.

Pharma & food barrier - blister and pouch foil where a single pinhole means spoilage.

Containers - takeaway trays, lunch boxes (3003 favored for strength).

Capacitor & technical - ultra-thin 1235 / 1xxx foil.

Lamination & composite - 8011 / 8079 as the barrier layer.

 

How we keep it from failing in your plant

The risk you care about: foil that looks fine on the roll but tears during slitting, or passes a pinhole that ruins a sealed pack.

What we check: before foil leaves the line, we measure thickness at set intervals across the web (micrometer / non-contact gauge) and inspect pinholes by light-transmission or dye-penetration on sampled reels - especially below ~0.05 mm. Every reel is logged with its reel ID and lot.

How we judge "pass": tolerances follow ASTM B479 or GB/T 3198 at the thickness class your order specifies. Food-contact grades are verified to FDA 21 CFR 175.300. We do not pass by eye. [Exact tolerance band per gauge: To be confirmed against your order spec.]

If something is off: the reel is quarantined, traced to its coil and lot, then reworked, downgraded, or confirmed with you - so a defect never reaches your line as a surprise.

 

Compliance & traceability

ISO 9001 quality system.

Food-contact grades compliant with FDA 21 CFR 175.300 on request.

SGS or equivalent test reports available per order.

Reel ID + lot recorded for full traceability.

 

FAQ

Q: What is your minimum order quantity? A: We keep MOQ flexible and accept small trial orders - tell us your spec and we will quote.

Q: What is your lead time? A: Typically 15–30 days from confirmed order, depending on alloy, gauge, and finish.

Q: Can you provide FDA compliance and test reports? A: Yes. Food-contact grades are supplied to FDA 21 CFR 175.300 where required, and SGS or equivalent test reports can be arranged per order.

Q: How do you guarantee thickness and pinhole quality? A: By measured inspection against ASTM B479 / GB/T 3198 at your specified gauge class - not by visual check. See the quality section above.

Q: Can you customize alloy, gauge, width, or temper? A: Yes. Send your target alloy, gauge, width, and end-use; we will confirm feasibility and tolerance.

Q: What if a reel is defective after arrival? A: Each reel carries a reel ID and lot. Contact us with the ID and we trace, verify, and resolve - rework, replacement, or credit as agreed.

 

GNEE Aluminum Foil packaging

 

Get a quote in 24 hours

Tell us four things and we will respond fast:

Alloy / temper

Gauge and width

End-use (food, pharma, container, technical)

Estimated quantity and destination

Email your spec to [GNEE] or use the inquiry form. Flexible MOQ, 15–30 day lead time, full traceability, FDA-grade options on request.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry